Calorimetry: Ice-Water Mixture Numericals for Class 11
Solve ice-water mixture numericals for Class 11 Physics and JEE. Check melting first, then find final temperature or ice left with three worked examples.

| Topic | Exam Prep |
|---|---|
| Read time | 5 min |
| Words | 840 |
| Published | 16 Nov 2026 |
| Best for | Parents & students |
Before finding the final temperature of an ice-water mixture, check whether the warm water can melt all the ice. If some ice remains in equilibrium with liquid water at ordinary atmospheric pressure, the mixture is at 0°C. Only after all the ice has melted can leftover heat raise the liquid's temperature above 0°C.
This guide gives original practice numericals for CBSE Class 11 Physics and JEE preparation. The ideas come from NCERT's Thermal Properties of Matter chapter: heat balance, specific heat capacity and latent heat. Calorimetry and change of state are listed in the CBSE 2026-27 Physics syllabus. The questions below are not claimed as past exam questions.
Set the assumptions and units first
Assume an insulated container with negligible heat capacity, no evaporation and enough time to reach thermal equilibrium. Use pure ice and water at ordinary atmospheric pressure. These assumptions remove heat exchanges that would otherwise need separate terms.
For our practice calculations, take water's specific heat capacity as 4.2 J per gram per °C, ice's as 2.1 J per gram per °C, and latent heat of fusion as 336 J per gram. These are supplied rounded values for these examples. If your question gives different constants, use those instead. Keep masses in grams with these units.
Heating or cooling without a phase change uses Q = mcΔT. Melting ice already at 0°C uses Q = mL. Melting does not itself increase temperature: the energy changes the state.
Example 1: some ice remains
Mix 25 g of ice at 0°C with 60 g of water at 20°C. Find the final temperature and the mass of ice left.
The warm water can release 60 × 4.2 × 20 = 5,040 J while cooling to 0°C. Melting all the ice would require 25 × 336 = 8,400 J. The available heat is smaller, so complete melting is impossible under the stated assumptions.
Ice melted = 5,040/336 = 15 g. Ice remaining = 25 - 15 = 10 g. The final state is 75 g of liquid water plus 10 g of ice, all at 0°C. Check mass: 75 + 10 = 85 g, matching the initial 60 + 25.
Do not use a single all-melted equation and accept a negative answer here. It would contradict the assumed final state. The comparison at 0°C tells you which calculation is physically valid.
Example 2: all the ice melts
Now mix the same 25 g of ice at 0°C with 100 g of water at 40°C. The water could release 100 × 4.2 × 40 = 16,800 J on cooling to 0°C. Complete melting still needs 8,400 J, leaving 8,400 J after melting.
That surplus warms all 125 g of liquid, rather than either initial portion alone. Therefore, 125 × 4.2 × T = 8,400, giving T = 16°C.
You can check with the direct balance: 100 × 4.2 × (40 - 16) = 25 × 336 + 25 × 4.2 × 16. Both sides equal 10,080 J. The final temperature lies between 0°C and 40°C, as expected.
Example 3: the ice starts below zero
Mix 20 g of ice at -10°C with 100 g of water at 30°C. First warm the ice to 0°C: Q = 20 × 2.1 × 10 = 420 J. Then melt it: Q = 20 × 336 = 6,720 J. Total heat needed before any melted water warms above zero is 7,140 J.
The water can supply 100 × 4.2 × 30 = 12,600 J on cooling to zero. All the ice melts, leaving 12,600 - 7,140 = 5,460 J. Spread this over 120 g of liquid: T = 5,460/(120 × 4.2) = 10.83°C approximately.
The first 420 J cannot be skipped. Nor should ice's specific heat be used to warm the melted liquid; after melting, use water's specific heat.
When the usual shortcut needs more care
If the available heat exactly equals the heat needed to bring the ice to zero and melt it, the final state is liquid water at 0°C. If a calorimeter has appreciable heat capacity, include its heat exchange. Ice far below zero can also freeze some initial water, so do not assume every problem fits the two simple branches above.
For more support with setting up energy balances, see physics tuition. Bring the constants and your attempted equation, not only the final answer.
Frequently asked questions
Why does an ice-water mixture stay at 0°C?
For pure ice and water in equilibrium at ordinary atmospheric pressure, heat supplied during melting changes the state rather than raising the temperature.
Do I always add a latent-heat term?
Add it when a phase change occurs. Warming ice from a negative temperature to 0°C is a separate specific-heat calculation.
Which mass is used after all the ice melts?
Use the total final liquid mass when surplus heat warms the whole mixture, provided no water is lost.
Can I mix kilograms with constants given per gram?
Not directly. Convert the masses or constants first, then keep the same unit system throughout every heat term.
Related articles
- Median Class 11: Discrete Series and Cumulative Frequency
- Arithmetic Mean Class 11: Discrete Series Worked Examples
- Price Elasticity of Demand: Class 11 Worked Examples
- Depreciation Class 11: SLM and WDV Worked Examples
- Rectification of Errors: Suspense Account Examples
Explore related tuition services: IIT-JEE tuition · physics tuition · CBSE tuition