Thermal Expansion Class 11: Rod and Gap Worked Examples
Solve Class 11 thermal expansion numericals with original rod, composite rod and closing-gap examples. Check temperature changes, units and final lengths.

| Topic | Exam Prep |
|---|---|
| Focus | Class 11 |
| Read time | 5 min |
| Words | 875 |
| Published | 17 Nov 2026 |
| Best for | Parents & students |
A rod that grows by 0.8 mm does not finish at a length of 0.8 mm. That number is its extra length. Thermal-expansion numericals become much easier when you keep the original length, the change in length and the final length separate.
This Class 11 Physics practice lesson uses three original examples: one freely expanding rod, two joined rods and a closing gap. The numerical coefficients below are supplied practice data, not measurements from an experiment. Use the coefficient and temperature range stated in your own question.
Set up the linear-expansion calculation
For a small expansion with an approximately constant coefficient, write ΔL = αL₀ΔT. Here L₀ is the original length at the initial temperature, α is the coefficient of linear expansion, and ΔT = final temperature minus initial temperature. The final length is L = L₀ + ΔL.
A temperature rise of 40°C is also a rise of 40 K. Do not add 273.15 to a temperature difference. You can use α in K⁻¹ with a Celsius temperature difference because the interval sizes match. Keep all lengths in one unit until the final conversion.
The NCERT Thermal Properties of Matter chapter explains linear expansion and the difference between free expansion and restraint. Thermal expansion is also in the CBSE Physics syllabus. These are practice problems, not predictions of a particular exam paper.
Example 1: Find extra length and final length
A uniform metal rod is 1.60 m long at 20°C. It is heated uniformly to 70°C and can expand freely. Take α = 1.0 × 10⁻⁵ K⁻¹. Find its increase in length and final length.
The temperature rise is 70 − 20 = 50 K, not 70 K. Substitute the original length:
ΔL = (1.0 × 10⁻⁵) × 1.60 × 50 = 0.00080 m = 0.80 mm.
Therefore L = 1.60 + 0.00080 = 1.60080 m. The fractional change is 0.00080/1.60 = 0.00050, which is small. That check is consistent with the small-expansion model.
If the same rod returns to 20°C, it returns to its original length under this reversible idealisation. A cooling calculation needs a negative ΔT; a negative ΔL means contraction, not a negative final length.
Example 2: Add the expansions of joined rods
Rod A is 0.60 m long with αA = 2.0 × 10⁻⁵ K⁻¹. Rod B is 0.90 m long with αB = 1.0 × 10⁻⁵ K⁻¹. They are joined end to end, lie straight and have free outer ends. Both undergo a uniform 40 K temperature rise. Ignore external loads and friction.
Calculate each increase using its own original length and coefficient:
- ΔLA = (2.0 × 10⁻⁵) × 0.60 × 40 = 0.00048 m = 0.48 mm.
- ΔLB = (1.0 × 10⁻⁵) × 0.90 × 40 = 0.00036 m = 0.36 mm.
Total increase = 0.48 + 0.36 = 0.84 mm. The original combined length is 1.50 m, so the final combined length is 1.50084 m. Different coefficients alone do not require thermal stress in this freely expanding, end-to-end model.
Do not use the simple average of the two coefficients: the rods have different lengths. If an effective coefficient is requested, divide total expansion by total original length and ΔT. Here αeffective = 0.00084/(1.50 × 40) = 1.4 × 10⁻⁵ K⁻¹. It is a length-weighted result.
Example 3: Decide when a gap closes
Two rods face each other across a 1.20 mm gap at 25°C. Their outer ends are fixed to immovable supports, but their inner ends remain free until contact. Each rod is 1.00 m long, with α = 1.5 × 10⁻⁵ K⁻¹. Both heat uniformly. Find the temperature at first contact.
Each free inner end advances by αL₀ΔT. Both movements reduce the same gap, so add them:
0.00120 = 2 × (1.5 × 10⁻⁵) × 1.00 × ΔT.
This gives ΔT = 40 K and contact temperature = 25 + 40 = 65°C. A 20 K rise would close only 0.60 mm, leaving 0.60 mm. That half-rise check catches the mistake of counting only one rod.
Stop this free-expansion calculation at first contact. Further heating introduces restraint and can develop compressive stress. Do not extend the gap equation beyond contact or treat this idealised arrangement as railway design guidance.
Check the setup before the arithmetic
Mark which ends can move. Use each rod's own α and original length. State whether your answer is an increase, a final length or a contact temperature. If unit conversion is the weak point, review Class 11 units and measurements practice. For force-driven extension instead of heating, use the separate Young's modulus worked examples.
Frequently asked questions
Should I convert every Celsius temperature to kelvin?
Not for ΔT in this formula. Subtract the Celsius temperatures directly; the difference has the same numerical value in kelvin.
Does a longer rod have a larger coefficient?
No. Under the stated conditions, α describes the material. A longer rod expands more because L₀ is larger.
Do I add or subtract two expansions?
Draw the moving ends. For the facing rods in Example 3, both ends move into the gap, so their advances add.
Can I use the formula after the rods touch?
Not as an unrestricted-motion model. Once contact prevents further free growth, a stress and deformation analysis is needed.
Related articles
- Class 11 Python Chapter 5: Input, Operators and Errors
- CTET December 2026: Exam on Dec 12-13, Admit Card, and Your 8-Week Plan
- Commerce Tuition Near Me: How to Find the Right Tutor for Class 11 and 12
- CBSE Class 10 Date Sheet 2027: Official PDF and Subject Dates
- How to Reduce Exam Stress and Anxiety Before Boards: Proven Strategies
Explore related tuition services: IIT-JEE tuition · physics tuition · CBSE tuition