EZ Tuitions Logo
EZ Tuitions
Back to Blog

Young's Modulus: Wire Extension Numericals for Class 11

5 min read• 11/16/2026• By Ananya Sharma, Academic Content Lead, EZ Tuitions• Exam Prep

Solve Young's modulus numericals for Class 11 Physics and JEE. Work through wire extension, hanging loads, diameter conversions and ratio checks with answers.

Physics student studying a thin wire and small suspended mass on a tabletop stand at a home desk
Key facts about this article
TopicExam Prep
Read time5 min
Words867
Published16 Nov 2026
Best forParents & students

A wire twice as thick does not stretch half as much under the same pull. For a circular wire, cross-sectional area depends on the square of its diameter, so doubling the diameter reduces the extension to one quarter. That squared term explains many wrong answers in Young's modulus numericals.

This Class 11 Physics and JEE practice guide uses original questions on wire extension, suspended loads and comparisons. The definitions follow NCERT's Mechanical Properties of Solids chapter. Young's modulus is also listed in the CBSE 2026-27 Physics syllabus. These are practice examples, not predictions about an examination.

Start with stress divided by strain

For a uniform wire of original length L, cross-sectional area A and extension e under tensile force F:

Stress = F/A; strain = e/L.
Young's modulus Y = (F/A)/(e/L) = FL/(Ae).
Therefore extension e = FL/(AY).

Strain has no unit because it divides one length by another. Stress and Y have the unit pascal, equivalent to N/m2. Extension has a length unit; it is not the same quantity as strain.

Use this linear relation within the proportional region of the stress-strain curve. Assume small extensions, a fixed temperature and a uniform wire. In the examples below, neglect the wire's own weight. Do not carry the same formula unchanged into a situation involving permanent deformation or a changing material response.

Example 1: the area is supplied directly

A wire is 1.5 m long and has area 0.50 mm2. A tensile force of 40 N acts on it. Take Y = 2.0 x 1011 Pa and find its extension.

Convert area before substituting: 0.50 mm2 = 0.50 x 10-6 m2. A square millimetre is one millionth of a square metre, not one thousandth.

e = (40 x 1.5)/[(0.50 x 10-6) x (2.0 x 1011)]
= 60/100000 m
= 6.0 x 10-4 m = 0.60 mm.

Check by a second route. Stress = 40/(0.50 x 10-6) = 8.0 x 107 Pa. Strain = stress/Y = 4.0 x 10-4. Multiplying strain by the original 1.5 m length returns 0.00060 m. The two routes agree.

Example 2: convert a hanging mass into force

A separate wire has length 2.0 m, circular diameter 1.0 mm and Y = 2.0 x 1011 Pa. It supports a stationary mass of 3.14 kg. For this exercise use g = 10 m/s2 and pi = 3.14.

First, F = mg = 31.4 N. The wire's tension balances the hanging weight. Do not use 3.14 kg as the force, or add the support's reaction to get twice the tension.

Next, radius r = d/2 = 0.50 mm = 5.0 x 10-4 m. Thus A = pi r2 = 7.85 x 10-7 m2.

e = (31.4 x 2.0)/[(7.85 x 10-7) x (2.0 x 1011)]
= 4.0 x 10-4 m = 0.40 mm.

Using the diameter as the radius would make the area four times too large and the calculated extension four times too small. Writing A = pi d2/4 avoids that particular substitution error.

Compare wires without repeating every number

For wires at the same temperature and within the same linear conditions, compare e = FL/(AY). If the material is unchanged, Y cancels. For circular wires, area is proportional to d2.

Suppose wire B has three times wire A's length, twice its diameter and twice its applied force. Both are made from the same material. Then eB/eA = (2 x 3)/22 = 1.5. If A extends by 0.40 mm, B extends by 0.60 mm.

Changing the dimensions changes how much the wire stretches; it does not, by itself, change the material's Young's modulus. Do not confuse Y with wire stiffness F/e = AY/L. A longer wire is less stiff under these assumptions even though its material has the same Y.

A short self-check

Take Example 1 and keep its force, material and length unchanged. Make the circular wire's diameter three times as large. What happens to the extension?

The area becomes nine times as large, so e becomes 0.60/9 = approximately 0.067 mm. If you got 0.20 mm, you used diameter instead of area in the ratio. Keep extra digits during the calculation and round only the answer.

Before finishing, label every supplied length as original length, extension, radius or diameter. Check that the final result answers the requested quantity. For help diagnosing where your substitutions go wrong, see our Physics tuition guide and bring an attempted question to the lesson.

Frequently asked questions

Does a longer wire have a smaller Young's modulus?

Not merely because it is longer. Under the same material conditions, its extension changes with length while Y stays the same.

What is the unit of Young's modulus?

Pascal, or N/m2. It is stress divided by dimensionless strain.

Should a hanging mass be substituted directly for F?

No. For these stationary-load examples, use its weight mg in newtons.

Can I use e = FL/(AY) for any load?

No. These calculations assume the proportional, small-deformation regime. The linear model is not valid for arbitrary loading.

Explore related tuition services: IIT-JEE tuition · physics tuition · CBSE tuition