Stokes' Law Class 11: Terminal Velocity Worked Examples
Solve Class 11 Stokes law numericals with original terminal velocity, radius-ratio and viscosity examples. Check buoyancy, units and the limits of the model.

| Topic | Exam Prep |
|---|---|
| Read time | 5 min |
| Words | 815 |
| Published | 17 Nov 2026 |
| Best for | Parents & students |
A ball falling through oil can keep moving even when the resultant force is zero. At terminal speed, its weight is balanced by buoyancy and viscous drag. The ball has stopped accelerating, not stopped falling. That distinction is the starting point for Class 11 Stokes-law numericals.
This lesson uses original practice data to work through terminal speed, a size comparison and a viscosity measurement. The numbers are supplied assumptions, not measured properties of a named liquid. The topic appears in the CBSE Physics curriculum and NCERT's discussion of mechanical properties of fluids.
Write the three forces before the formula
For a small rigid sphere falling through a still liquid, weight acts downwards. Buoyancy and drag act upwards. Write the sphere density as ρs, liquid density as ρf, radius as r, liquid viscosity as η and terminal speed as vt.
Stokes' drag is F = 6πηrv. The sphere's volume is V = 4πr³/3. At terminal speed, ρsVg = ρfVg + 6πηrvt. Substituting the volume and cancelling gives:
vt = 2r²(ρs − ρf)g / (9η).
Here the sphere must be denser than the liquid for downward settling. Use SI units: r in metres, densities in kg/m³ and η in Pa s. The result is in m/s. If you need a conversion refresher, practise our Class 11 units and measurements examples first.
Example 1: diameter, buoyancy and terminal speed
A rigid sphere has diameter 0.40 mm and density 3,500 kg/m³. It falls in a liquid of density 1,000 kg/m³ and viscosity 0.20 Pa s. Take g = 10 m/s². Assume Stokes' law applies. Find its terminal speed.
The radius is half the diameter: r = 0.20 mm = 2.0 × 10⁻⁴ m. Therefore r² = 4.0 × 10⁻⁸ m². The density difference is 3,500 − 1,000 = 2,500 kg/m³.
Substitution gives vt = (2 × 4.0 × 10⁻⁸ × 2,500 × 10)/(9 × 0.20) = 0.002/1.8 = 1.11 × 10⁻³ m/s, approximately. That is 1.11 mm/s, not 1.11 m/s.
Using the diameter as r would make r² four times too large and predict four times the speed. Ignoring buoyancy would replace the density difference with 3,500 and overestimate the speed by a factor of 1.4. Neither error is a rounding issue.
Example 2: change the radius and viscosity together
Keep the same sphere material and liquid density, but double the sphere's radius and use a liquid with three times the original viscosity. Assume the new situation also remains within the Stokes regime. Find the new terminal speed relative to the old one.
At fixed density difference and g, vt is proportional to r²/η. Hence vt,new/vt,old = 2²/3 = 4/3. Using the unrounded result from Example 1 gives 1.48 × 10⁻³ m/s, approximately.
The larger radius increases the predicted speed, while the higher viscosity reduces it. Keep both changes in the ratio. The familiar statement that doubling the radius quadruples terminal speed applies only when viscosity and the density difference are unchanged.
Example 3: calculate viscosity from a timed fall
A different rigid sphere has radius 0.30 mm and density 4,000 kg/m³. The liquid density is 1,000 kg/m³. After reaching terminal speed, the sphere travels 0.080 m between two marks in 20 s. Take g = 10 m/s² and assume Stokes' law is valid.
First find vt = distance/time = 0.080/20 = 0.0040 m/s. Rearrange the terminal-speed equation:
η = 2r²(ρs − ρf)g/(9vt) = (2 × 9.0 × 10⁻⁸ × 3,000 × 10)/(9 × 0.0040) = 0.0054/0.036 = 0.15 Pa s.
The timing must describe the steady part of the fall. An average speed measured immediately after release is not automatically the terminal speed. Keep the sphere away from nearby walls and the bottom, since the simple model assumes their effect is negligible.
Know when to stop using this model
NCERT explains Stokes' law for viscous drag and the terminal balance. Use it for slow motion of a small rigid sphere under suitable flow conditions. Do not apply the radius-squared rule automatically to a parachutist, a large raindrop or a fast ball. Their drag need not follow 6πηrv.
For revision, cover each solution and write the force balance again. Then change one input and predict the direction of the change before calculating. A terminal-speed answer should still describe motion, with zero acceleration and nonzero forces.
Frequently asked questions
Does terminal velocity mean that the ball stops?
No. Its velocity becomes constant because the resultant force is zero. Weight, buoyancy and drag still act.
Should I use radius or diameter in Stokes' law?
Use radius. Halve a supplied diameter before converting and squaring it in the terminal-speed equation.
Why is the liquid density subtracted?
Buoyancy supports part of the sphere's weight. The drag balances weight minus buoyancy at terminal speed.
Does a larger sphere always follow the radius-squared rule?
No. That comparison requires the stated density and viscosity conditions and a valid Stokes-flow model for both spheres.
Related articles
- Thermal Expansion Class 11: Rod and Gap Worked Examples
- Young's Modulus: Wire Extension Numericals for Class 11
- Calorimetry: Ice-Water Mixture Numericals for Class 11
- Median Class 11: Discrete Series and Cumulative Frequency
- Arithmetic Mean Class 11: Discrete Series Worked Examples
Explore related tuition services: IIT-JEE tuition · physics tuition · CBSE tuition